NI 6239 Introduction

Download PDF

Updated2023-02-18
10 minute(s) read

The following specifications are typical at 25 °C, unless otherwise noted. For more information about the NI 6239, refer to the NI 6238/6239 User Manual available from ni.com/manuals.

Analog Input

Number of channels

8 differential current inputs

Ground reference

AI GND

ADC resolution

16 bits

DNL

No missing codes guaranteed

INL

Refer to the AI Absolute Accuracy section

Sample rate
Maximum	250 kS/s
Minimum	No minimum

Timing accuracy

50 ppm of sample rate

Timing resolution

50 ns

Input coupling

Input range

±20 mA

Maximum working voltage for analog inputs

Refer to the Maximum Working Voltage section

Input impedance (AI+ to AI-)

92 Ω ±10% in parallel with 100 pF

Maximum input impedance

100 Ω (at 55 °C)

Input bias current

±100 pA

Small signal bandwidth (-3 dB)

700 kHz

Input FIFO size

4,095 samples

Scan list memory

4,095 entries

Data transfers

DMA (scatter-gather), interrupts, programmed I/O

Input current during overvoltage condition

±20 mA maximum/AI pin

Overcurrent protection

±40 mA maximum^[1]

Overvoltage protection (AI x+ or AI x- with respect to AI GND)^[2]
Device on	±25 V for up to two AI pins
Device off	±15 V for up to two AI pins

Typical Performance Graphs

1378 — Figure 1. AI Small Signal Bandwidth

AI Absolute Accuracy

Note Accuracies listed are valid for up to one year from the device external calibration.

Table 1. AI Absolute Accuracy
Nominal Range Positive Full Scale	Nominal Range Negative Full Scale	Residual Gain Error (ppm of Reading)	Residual Offset Error (ppm of Range)	Offset Tempco (ppm of Range/°C)	Random Noise, σ (μArms)	Absolute Accuracy at Full Scale (μA)	Sensitivity (μA)
0.02	-0.02	595	100	79	0.6	18.9	0.24

Note Sensitivity is the smallest current change that can be detected. It is a function of noise.

Gain tempco	35 ppm/°C
Reference tempco	5 ppm/°C
INL error	76 ppm of range

AI Absolute Accuracy Equation

AbsoluteAccuracy = Reading · (GainError) + Range · (OffsetError) + NoiseUncertainty

GainError = ResidualAIGainError + GainTempco · (TempChangeFromLastInternalCal) + ReferenceTempco · (TempChangeFromLastExternalCal)
OffsetError = ResidualAIOffsetError + OffsetTempco · (TempChangeFromLastInternalCal) + INLError
NoiseUncertainty =
$\frac{Random Noise \cdot 3}{\sqrt{100}}$
for a coverage factor of 3 σ and averaging 100 points.

AI Absolute Accuracy Example

Absolute accuracy at full scale on the analog input channels is determined using the following assumptions:

TempChangeFromLastExternalCal = 10 °C
TempChangeFromLastInternalCal = 1 °C
number_of_readings = 100
CoverageFactor = 3 σ

For example, on the 20 mA range, the absolute accuracy at full scale is as follows:

GainError = 595 ppm + 35 ppm · 1 + 5 ppm · 10 = 680 ppm
OffsetError = 100 ppm + 79 ppm · 1 + 76 ppm = 255 ppm
NoiseUncertainty =
$\frac{.6 µ A \cdot 3}{\sqrt{100}}$
= .18 µA
AbsoluteAccuracy = 20 mA · (GainError) + 20 mA · (OffsetError) + NoiseUncertainty = 18.9 µA

Analog Output

Number of channels

2 current outputs

Ground reference

AO GND

DAC resolution

16 bits

Maximum update rate
1 channel	500 kS/s
2 channels	450 kS/s per channel

Timing accuracy

50 ppm of sample rate

Timing resolution

50 ns

Output range

0 mA to 20 mA

Output coupling

Power-on state

0 mA

Power-on glitch

None

Output FIFO size

8,191 samples shared among channels used

Data transfers

DMA (scatter-gather), interrupts, programmed I/O

AO waveform modes

Non-periodic waveform, periodic waveform regeneration mode from onboard FIFO, periodic waveform regeneration from host buffer including dynamic update

External power supply

10 VDC to 30 VDC, refer to the figure

External power supply consumption

50 mA maximum, refer to the figure

Internal voltage drop

3 V maximum, refer to the figure

Maximum resistive load

Up to 1 kΩ with 24 V power supply connected; refer to the figure

Protection	Open and short circuit
Slew rate	0.1 mA/μS

AO Absolute Accuracy

Absolute accuracy at full-scale numbers is valid immediately following internal calibration and assumes the device is operating within 10 °C of the last external calibration.

Note Accuracies listed are valid for up to one year from the device external calibration.

Table 2. AO Absolute Accuracy
Nominal Range Positive Full Scale (A)	Nominal Range Negative Full Scale (A)	Residual Gain Error (% of Reading)	Gain Tempco (ppm/°C)	Residual Offset Error (ppm of Range)	Offset Tempco (ppm of Range/°C)	Absolute Accuracy at Full Scale (μA)
0.02	0	0.1570	20	0.0537	8	52.3

Reference tempco	5 ppm/°C
INL error	128 ppm of range
Random noise	2 μA

AO Absolute Accuracy Equation

AbsoluteAccuracy = OutputValue · (GainError) + Range · (OffsetError)

GainError = ResidualGainError + GainTempco · (TempChangeFromLastInternalCal) + ReferenceTempco · (TempChangeFromLastExternalCal)
OffsetError = ResidualOffsetError + AOOffsetTempco · (TempChangeFromLastInternalCal) + INLError

Digital I/O/PFI

Static Characteristics

Number of channels	10 total
Number of input channels	6 (PFI <0..5>/P0.<0..5>)
Number of output channels	4 (PFI <6..9>/P1.<0..3>)
Direction control	Fixed, lines are unidirectional

PFI/Port 0/Port 1 Functionality

PFI <0..5>/P0.<0..5>	Static digital input, timing input
PFI <6..9>/P1.<0..3>	Static digital output, timing output
Timing output sources	Many AI, AO, counter timing signals
Debounce filter settings	125 ns, 6.425 µs, 2.56 ms, disable; high and low transitions; selectable per input

Digital Input (Port 0)

Number of channels

Ground reference

P0.GND

Input voltage range

0 V to 30 V

Minimum pulse width for timing signal

0.5 μs

Logic "0" level

0 V to 4 V

Logic "1" level

10 V to 30 V

Minimum input impedance

3.3 kΩ

Typical input current

7 mA at 24 V input, 2.5 mA at 8 V input

Maximum input current

9 mA

Propagation delay
Low to high	150 ns, typical
High to low	100 ns, typical

Digital Output (Port 1)

Number of channels	4
Ground reference	P1.GND
Device output type	DO sink

The following figure shows PO.<0..5> and PI.<0..3> on the NI 6239 device.

Maximum external supply voltage (P1.VCC)

30 V

On state saturation voltage

1.6 V maximum at 350 mA

Off state leakage

50 µA

Maximum current

100 mA for each line for simultaneous usage, 350 mA for single line usage

Minimum pulse width for timing signal (sink output)

1.25 µs

Propagation delay (sink output)
Open to close	0.4 µs
Close to open	0.4 µs

General-Purpose Counters/Timers

Number of counter/timers	2
Resolution	32 bits
Counter measurements	Edge counting, pulse, semi-period, period, two-edge separation
Position measurements	X1, X2, X4 quadrature encoding with Channel Z reloading; two-pulse encoding
Output applications	Pulse, pulse train with dynamic updates, frequency division, equivalent time sampling
Internal base clocks	80 MHz, 20 MHz, 0.1 MHz
External base clock frequency	0 MHz to 20 MHz
Base clock accuracy	50 ppm
Inputs	Gate, Source, HW_Arm, Aux, A, B, Z, Up_Down
Routing options for inputs	Any input PFI, RTSI, PXI_TRIG, PXI_STAR, many internal signals
FIFO	2 samples
Data transfers	Dedicated scatter-gather DMA controller for each counter/timer; interrupts; programmed I/O

Frequency Generator

Number of channels	1
Base clocks	10 MHz, 100 kHz
Divisors	1 to 16
Base clock accuracy	50 ppm

Output can be available on any output PFI or RTSI terminal.

Phase-Locked Loop (PLL)

Number of PLLs	1
Reference signal	PXI_STAR, PXI_CLK10, RTSI <0..7>
Output of PLL	80 MHz Timebase; other signals derived from 80 MHz Timebase including 20 MHz and 100 kHz Timebases

External Digital Triggers

Source	Any PFI, RTSI, PXI_TRIG, PXI_STAR
Polarity	Software-selectable for most signals
Analog input function	Start Trigger, Reference Trigger, Pause Trigger, Sample Clock, Convert Clock, Sample Clock Timebase
Analog output function	Start Trigger, Pause Trigger, Sample Clock, Sample Clock Timebase
Counter/timer function	Gate, Source, HW_Arm, Aux, A, B, Z, Up_Down

Device-to-Device Trigger Bus

PCI	RTSI <0..7>^[3]
PXI	PXI_TRIG <0..7>, PXI_STAR
Output selections	10 MHz Reference Clock, frequency generator output, many internal signals
Debounce filter settings	125 ns, 6.425 μs, 2.56 ms, disable; high and low transitions; selectable per input

Bus Interface

PCI/PXI

3.3 V or 5 V signal environment

The PXI device can be installed in PXI slots or PXI Express hybrid slots.

DMA channels

4, analog input, analog output, counter/timer 0, counter/timer 1

Power Requirements

Current draw from bus during no-load condition
+5 V	0.7 A
+12 V	20 mA

Current draw from bus during AI and AO overvoltage condition
+5 V	0.95 A
+12 V	20 mA

Physical Characteristics

Dimensions
PCI printed circuit board	9.7 cm × 15.5 cm(3.8 in. × 6.1 in.)
PXI printed circuit board	Standard 3U PXI

Weight
PCI	103 g (3.6 oz)
PXI	144 g (5.1 oz)

I/O connector

37-pin D-SUB

Calibration

Recommended warm-up time	15 minutes
Calibration interval	1 year

Maximum Working Voltage

Connect only voltages that are below these limits.

Channel-to-earth ground^[4]
Continuous	≤30 Vrms/60 VDC Measurement Category I
Withstand	≤840 Vrms/1,200 VDC, verified by a 5 s dielectric withstand test

Channel-to-bus^[5]
Continuous	≤30 Vrms/60 VDC Measurement Category I
Withstand	≤1,400 Vrms/1,950 VDC, verified by a 5 s dielectric withstand test

Analog channel-to-AI GND or AO GND (in the following figure, |V_a - V_b|)

≤11 V, Measurement Category I

Digital channel-to-P1.GND or P0.GND (in the following figure, |V_c - V_d| or |V_e - V_f|)

≤30 V, Measurement Category I

Measurement Category I is for measurements performed on circuits not directly connected to the electrical distribution system referred to as MAINS voltage. MAINS is a hazardous live electrical supply system that powers equipment. This category is for measurements of voltages from specially protected secondary circuits. Such voltage measurements include signal levels, special equipment, limited-energy parts of equipment, circuits powered by regulated low-voltage sources, and electronics.

Caution This device is rated for Measurement Category I and the voltage across the isolation barrier is limited to no greater than 30 Vrms/60 VDC/42.4 V_pk continuous. These test and measurement circuits are not intended for direct connection to the MAINS building installations of Measurement Categories CAT II, CAT III, or CAT IV.

The following figure illustrates the safety voltages specifications.

Environmental

Operating temperature	0 ºC to 55 ºC
Storage temperature	-20 ºC to 70 ºC
Humidity	10% RH to 90% RH, noncondensing
Maximum altitude	2,000 m
Pollution Degree (indoor use only)	2

Indoor use only.

Shock and Vibration (PXI Only)

Operational shock

30 g peak, half-sine, 11 ms pulse (Tested in accordance with IEC 60068-2-27. Test profile developed in accordance with MIL-PRF-28800F.)

Random vibration
Operating	5 Hz to 500 Hz, 0.3 g_rms
Nonoperating	5 Hz to 500 Hz, 2.4 g_rms (Tested in accordance with IEC 60068-2-64. Nonoperating test profile exceeds the requirements of MIL-PRF-28800F, Class 3.)

Safety Compliance Standards

This product is designed to meet the requirements of the following electrical equipment safety standards for measurement, control, and laboratory use:

IEC 61010-1, EN 61010-1
UL 61010-1, CSA C22.2 No. 61010-1

Note For safety certifications, refer to the product label or the Product Certifications and Declarations section.

Electromagnetic Compatibility

CE Compliance

2011/65/EU; Restriction of Hazardous Substances (RoHS)

Product Certifications and Declarations

Refer to the product Declaration of Conformity (DoC) for additional regulatory compliance information. To obtain product certifications and the DoC for NI products, visit ni.com/product-certifications, search by model number, and click the appropriate link.

Environmental Management

NI is committed to designing and manufacturing products in an environmentally responsible manner. NI recognizes that eliminating certain hazardous substances from our products is beneficial to the environment and to NI customers.

For additional environmental information, refer to the Engineering a Healthy Planet web page at ni.com/environment. This page contains the environmental regulations and directives with which NI complies, as well as other environmental information not included in this document.

EU and UK Customers

Waste Electrical and Electronic Equipment (WEEE)—At the end of the product life cycle, all NI products must be disposed of according to local laws and regulations. For more information about how to recycle NI products in your region, visit ni.com/environment/weee.

电子信息产品污染控制管理办法（中国RoHS）

中国RoHS— NI符合中国电子信息产品中限制使用某些有害物质指令(RoHS)。关于NI中国RoHS合规性信息，请登录 ni.com/environment/rohs_china。(For information about China RoHS compliance, go to ni.com/environment/rohs_china.)

Device Pinout

¹ Any voltage applied resulting in current flowing above 40 mA can damage the device permanently.

² This overvoltage protection triggers after the overcurrent protection is in effect.

³ In other sections of this document, RTSI refers to RTSI <0..7> for the PCI devices or PXI_TRIG <0..7> for PXI devices.

⁴ In the figure, |V_a – V_h|, |V_c – V_h|, and |V_e – V_h|.

⁵ In the figure, |V_a – V_g|, |V_c – V_g|, and |V_e – V_g|.

Was this information helpful?

Yes No

PCI/PXI-6239 Specifications

M Series Data Acquisition: 16-Bit, 250 kS/s, 8 AI, 2 AO, 24 DIO Sinking, Current Input/Output Bank Isolation

Filters

Content Type

Programming Language

Analog Input

Typical Performance Graphs

AI Absolute Accuracy

AI Absolute Accuracy Equation

AI Absolute Accuracy Example

Analog Output

AO Absolute Accuracy

AO Absolute Accuracy Equation

Digital I/O/PFI

Static Characteristics

PFI/Port 0/Port 1 Functionality

Digital Input (Port 0)

Digital Output (Port 1)

General-Purpose Counters/Timers

Frequency Generator

Phase-Locked Loop (PLL)

External Digital Triggers

Device-to-Device Trigger Bus

Bus Interface

Power Requirements

Physical Characteristics

Calibration

Maximum Working Voltage

Environmental

Shock and Vibration (PXI Only)

Safety Compliance Standards

Electromagnetic Compatibility

CE Compliance

Product Certifications and Declarations

Environmental Management

EU and UK Customers

电子信息产品污染控制管理办法（中国RoHS）

Device Pinout

In This Section