NI-9229 and sbRIO-9229 Specifications

Connector Types

The NI-9229 has more than one connector type: NI-9229 with screw terminal and NI-9229 with BNC. Unless the connector type is specified, NI-9229 refers to both connector types.

Definitions

Warranted specifications describe the performance of a model under stated operating conditions and are covered by the model warranty.

Characteristics describe values that are relevant to the use of the model under stated operating conditions but are not covered by the model warranty.

  • Typical specifications describe the performance met by a majority of models.
  • Nominal specifications describe an attribute that is based on design, conformance testing, or supplemental testing.

Specifications are Typical unless otherwise noted.

Conditions

Specifications are valid for the range -40 °C to 70 °C unless otherwise noted. All voltages are relative to the AI- signal on each channel unless otherwise noted.

Input Characteristics

Number of channels

4 analog input channels

ADC resolution

24 bits

Type of ADC

Delta-Sigma (with analog prefiltering)

Sampling mode

Simultaneous

Internal master timebase (fM)

Frequency

12.8 MHz

Accuracy

±100 ppm maximum

Data rate range (fs) using internal master timebase

Minimum

1.613 kS/s

Maximum

50 kS/s

Data rate range (fs) using external master timebase

Minimum

390.625 S/s

Maximum

51.2 kS/s

Figure 1. Data Rates[1]1 The data rate must remain within the appropriate data rate range. (fs)
fM÷256n,n=1,2,...,31
Input voltage ranges (AI+ to AI-)

Nominal

±60 V

Typical

±62.64 V

Minimum

±61.5 V

Overvoltage protection

±100 V

Input coupling

DC

Input impedance (AI+ to AI-)

1 MΩ

Table 1. NI-9229 Accuracy
Measurement Conditions Percent of Reading (Gain Error) Percent of Range[2]2 Range equals 62.64 V (Offset Error)
Calibrated Typical (25 °C, ±5 °C) ±0.03% ±0.008%
Maximum (-40 °C to 70 °C) ±0.13% ±0.05%
Uncalibrated[3]3 Uncalibrated accuracy refers to the accuracy achieved when acquiring in raw or unscaled modes where the calibration constants stored in the module are not applied to the data. Typical (25 °C, ±5 °C) ±0.3% ±0.11%
Maximum (-40 °C to 70 °C) ±1.2% ±0.55%

Input noise

320 μV rms

Stability

Gain drift

±5 ppm/°C

Offset drift

±150 μV/°C

Post-calibration gain match (channel-to-channel, 20 kHz)

0.22 dB maximum

Phase mismatch

Channel-to-channel

0.045°/kHz maximum

Module-to-module

(0.045°/kHz · fin) + (360° · fin/fM)

Phase nonlinearity (fs = 50 kS/s)

0.11° maximum

Figure 2. Input delay
40+5512/fs+3.3μs
Passband

Frequency

0.453 · fs

Flatness (fs = 50 kS/s)

±100 mdB maximum

Stopband

Frequency

0.547 · fs

Rejection

100 dB

Alias-free bandwidth

0.453 · fs

-3 dB prefilter bandwidth (fs = 50 kS/s)

24.56 kHz

Crosstalk (1 kHz)

-130 dB

CMRR (fin = 60 Hz)

116 dB

SFDR (1 kHz, -60 dBFS)

128 dBFS

Total Harmonic Distortion (THD)

1 kHz, -1 dBFS

-99 dB

1 kHz, -20 dBFS

-105 dB

MTBF

NI-9229 with screw terminal

662,484 hours at 25 °C; Bellcore Issue 6, Method 1, Case 3, Limited Part Stress Method

NI-9229 with BNC

864,132 hours at 25 °C; Bellcore Issue 6, Method 1, Case 3, Limited Part Stress Method

Power Requirements

Power consumption from chassis
Active mode

NI-9229 with screw terminal

740 mW maximum

NI-9229 with BNC

800 mW maximum

Sleep mode

25 μW maximum

Thermal dissipation
Active mode

NI-9229 with screw terminal

760 mW maximum

NI-9229 with BNC

820 mW maximum

Sleep mode

16 mW maximum

Physical Characteristics

Dimensions

Visit ni.com/dimensions and search by module number.

Weight

NI-9229 with screw terminal

147 g (5.2 oz)

NI-9229 with BNC

169 g (6.0 oz)

Screw-terminal wiring

Gauge

0.05 mm2 to 1.5 mm2 (30 AWG to 14 AWG) copper conductor wire

Wire strip length

6 mm (0.24 in.) of insulation stripped from the end

Temperature rating

90 °C, minimum

Torque for screw terminals

0.22 N · m to 0.25 N · m (1.95 lb · in. to 2.21 lb · in.)

Wires per screw terminal

One wire per screw terminal; two wires per screw terminal using a 2-wire ferrule

Ferrules

0.25 mm2 to 1.5 mm2

Connector securement

Securement type

Screw flanges provided

Torque for screw flanges

0.2 N · m (1.80 lb · in.)

NI-9229 with Screw Terminal Safety Voltages

Connect only voltages that are within the following limits:

Isolation
Channel-to-channel

Continuous

250 V RMS, Measurement Category II

Withstand

1,390 V, verified by a 5 s dielectric withstand test

Channel-to-earth ground

Continuous

250 V RMS, Measurement Category II

Withstand

2,300 V, verified by a 5 s dielectric withstand test

Explosive atmospheres

Channel-to-channel

60 V DC, Measurement Category I

Channel-to-earth ground

60 V DC, Measurement Category I

Measurement Categories

Measurement Category I

Warning Do not connect the product to signals or use for measurements within Measurement Categories II, III, or IV, or for measurements on MAINs circuits or on circuits derived from Overvoltage Category II, III, or IV which may have transient overvoltages above what the product can withstand. The product must not be connected to circuits that have a maximum voltage above the continuous working voltage, relative to earth or to other channels, or this could damage and defeat the insulation. The product can only withstand transients up to the transient overvoltage rating without breakdown or damage to the insulation. An analysis of the working voltages, loop impedances, temporary overvoltages, and transient overvoltages in the system must be conducted prior to making measurements.
Mise en garde Ne pas connecter le produit à des signaux dans les catégories de mesure II, III ou IV et ne pas l'utiliser pour des mesures dans ces catégories, ou des mesures sur secteur ou sur des circuits dérivés de surtensions de catégorie II, III ou IV pouvant présenter des surtensions transitoires supérieures à ce que le produit peut supporter. Le produit ne doit pas être raccordé à des circuits ayant une tension maximale supérieure à la tension de fonctionnement continu, par rapport à la terre ou à d'autres voies, sous peine d'endommager et de compromettre l'isolation. Le produit peut tomber en panne et son isolation risque d'être endommagée si les tensions transitoires dépassent la surtension transitoire nominale. Une analyse des tensions de fonctionnement, des impédances de boucle, des surtensions temporaires et des surtensions transitoires dans le système doit être effectuée avant de procéder à des mesures.

Measurement Category I is for measurements performed on circuits not directly connected to the electrical distribution system referred to as MAINS voltage. MAINS is a hazardous live electrical supply system that powers equipment. This category is for measurements of voltages from specially protected secondary circuits. Such voltage measurements include signal levels, special equipment, limited-energy parts of equipment, circuits powered by regulated low-voltage sources, and electronics.

Note Measurement Categories CAT I and CAT O are equivalent. These test and measurement circuits are for other circuits not intended for direct connection to the MAINS building installations of Measurement Categories CAT II, CAT III, or CAT IV.

Measurement Category II

Caution If using in explosive atmospheres, do not connect the NI-9229 with screw terminal to signals or use for measurements within Measurement Categories II, III, or IV.
Attention En cas d'utilisation dans des atmosphères explosibles, ne pas connecter le NI-9239 avec bornier à vis à des signaux ou l'utiliser pour effectuer des mesures dans les catégories de mesure II, III ou IV.
Caution Do not connect the NI-9229 with screw terminal to signals or use for measurements within Measurement Categories III or IV.
Attention Ne pas connecter le produit à des signaux dans les catégories de mesure III ou IV et ne pas l'utiliser pour effectuer des mesures dans ces catégories.

Measurement Category II is for measurements performed on circuits directly connected to the electrical distribution system. This category refers to local-level electrical distribution, such as that provided by a standard wall outlet, for example, 115 V for U.S. or 230 V for Europe.

NI-9229 with BNC Safety Voltages

Connect only voltages that are within the following limits:

Isolation
Channel-to-channel

Continuous

60 V DC, Measurement Category I

Withstand

1,000 V, verified by a 5 s dielectric withstand test

Channel-to-earth ground

Continuous

60 V DC, Measurement Category I

Withstand

1,000 V, verified by a 5 s dielectric withstand test

Measurement Category I

Caution Do not connect the NI-9229 with BNC to signals or use for measurements within Measurement Categories II, III, or IV.
Attention Ne pas connecter le produit à des signaux dans les catégories de mesure II, III ou IV et ne pas l'utiliser pour effectuer des mesures dans ces catégories.
Warning Do not connect the NI-9229 with BNC to signals or use for measurements within Measurement Categories II, III, or IV, or for measurements on MAINs circuits or on circuits derived from Overvoltage Category II, III, or IV which may have transient overvoltages above what the product can withstand. The product must not be connected to circuits that have a maximum voltage above the continuous working voltage, relative to earth or to other channels, or this could damage and defeat the insulation. The product can only withstand transients up to the transient overvoltage rating without breakdown or damage to the insulation. An analysis of the working voltages, loop impedances, temporary overvoltages, and transient overvoltages in the system must be conducted prior to making measurements.
Mise en garde Ne pas connecter le produit à des signaux dans les catégories de mesure II, III ou IV et ne pas l'utiliser pour des mesures dans ces catégories, ou des mesures sur secteur ou sur des circuits dérivés de surtensions de catégorie II, III ou IV pouvant présenter des surtensions transitoires supérieures à ce que le produit peut supporter. Le produit ne doit pas être raccordé à des circuits ayant une tension maximale supérieure à la tension de fonctionnement continu, par rapport à la terre ou à d'autres voies, sous peine d'endommager et de compromettre l'isolation. Le produit peut tomber en panne et son isolation risque d'être endommagée si les tensions transitoires dépassent la surtension transitoire nominale. Une analyse des tensions de fonctionnement, des impédances de boucle, des surtensions temporaires et des surtensions transitoires dans le système doit être effectuée avant de procéder à des mesures.

Measurement Category I is for measurements performed on circuits not directly connected to the electrical distribution system referred to as MAINS voltage. MAINS is a hazardous live electrical supply system that powers equipment. This category is for measurements of voltages from specially protected secondary circuits. Such voltage measurements include signal levels, special equipment, limited-energy parts of equipment, circuits powered by regulated low-voltage sources, and electronics.

Note Measurement Categories CAT I and CAT O are equivalent. These test and measurement circuits are for other circuits not intended for direct connection to the MAINS building installations of Measurement Categories CAT II, CAT III, or CAT IV.

Environmental Characteristics

Temperature

Operating

-40 °C to 70 °C

Storage

-40 °C to 85 °C

Humidity

Operating

10% RH to 90% RH, noncondensing

Storage

5% RH to 95% RH, noncondensing

Ingress protection

IP40

Pollution Degree

2

Maximum altitude

NI-9229 with screw terminal

2,000 m

NI-9229 with BNC

2,000 m

Shock and Vibration
Operating vibration

Random

5 g RMS, 10 Hz to 500 Hz

Sinusoidal

5 g, 10 Hz to 500 Hz

Operating shock

30 g, 11 ms half sine; 50 g, 3 ms half sine; 18 shocks at 6 orientations

To meet these shock and vibration specifications, you must panel mount the system.

Calibration

You can obtain the calibration certificate and information about calibration services for the NI-9229 at ni.com/calibration.

Calibration interval

1 year

1 The data rate must remain within the appropriate data rate range.

2 Range equals 62.64 V

3 Uncalibrated accuracy refers to the accuracy achieved when acquiring in raw or unscaled modes where the calibration constants stored in the module are not applied to the data.