Home Support Documentation Bugs

Calibration Executive 6.2 Bug Fixes

Created Jun 22, 2023

Overview

The following items are notable issues fixed between the release of Calibration Executive 6.1 and Calibration Executive 6.2, including additional patches and service packs. If you have an issue ID, you can search this list to validate that the issue has been fixed. This is not an exhaustive list of issues fixed in the current version of Calibration Executive.

Bug Number

Legacy ID

Description

Details
1313819

Error -1074118615 Occurs While Adjusting PXI-4110 Using CalExec 6.1

While running the adjustment procedure for PXI-4110, the following error occurs:

"Error -1074118615 occurred at niDCPower Cal Adjust Current Limit.vi at step Adjust Current Output AccuracyThe Measured Outputs array contains a value that is out of the permitted range."

Re-running the procedure produces the same result.

Workaround:

If error -1074118615 occurs during verification and adjustment (VA) using Calibration Executive version 6.1, use a previous version of Calibration Executive (e.g., 5.2.1, 6.0, or 6.0.1) to execute the VA operation for the DUT until a fix becomes available.

Reported Version:

Calibration Executive 6.1

Resolved Version:

Calibration Executive 6.2

Added:

Mar 17, 2021
1349950

Error -1074116167 Occurs Verifying an NI 54xx Device Using CalExec 6.1

During the Verify and Adjust procedure for certain NI 54xx devices, the following error occurs at the Re-Verify Direct Analog Path Flatness step:

"Error -1074116167 occurred at niFgen Create Waveform (DBL).vi at step Re-Verify Direct Analog Path FlatnessValues for AO channel properties lead to an output voltage that exceeds the maximum for the device."

Re-running the procedure produces the same result.

This issue affects the following models:

  • PCI-5421
  • PXI-5421
  • PXI-5422
  • PXI-5441
  • PXIe-5442

Workaround:

If error -1074116167 occurs during verification and adjustment (VA) using Calibration Executive version 6.1, use a previous version of Calibration Executive (e.g., 5.2.1, 6.0, or 6.0.1) to execute the VA operation for the DUT until a fix becomes available.

Reported Version:

Calibration Executive 6.1

Resolved Version:

Calibration Executive 6.2

Added:

Mar 17, 2021
1349313

TUR is Calculated Incorrectly for Single-Sided Limits When Neither Limit is +/- Inf

Single-sided limits are typically +Inf or -Inf, which automated calculation in Calibration Executive handles. However, if the non-limit side of a single-sided limit is any real number (not +/-Inf), Calibration Executive returns an incorrect Test Uncertainty Ratio (TUR).

Workaround:

Upgrade to Calibration Executive 6.2, and then apply UL or LL modifier in the uncertainty worksheet to specify the active limit for the test point. For more information, refer to "Measurement Guard Banding and TUR Support" in Calibration Executive 6.2 Help.

Reported Version:

Calibration Executive 6.1

Resolved Version:

Calibration Executive 6.2

Added:

May 3, 2021

Additional Patch Information

Installing some patches may require certain additional steps or considerations. Please refer to the following table for more information about patches for this release.

These patches currently do not have any special instructions.

Glossary of Terms

 

  • Bug ID - When an issue is reported to NI, you may be given this ID or find it on ni.com.  You may also find IDs posted by NI on the discussion forums or in KnowledgeBase articles.
  • Legacy ID – An older issue ID that refers to the same issue.  You may instead find this issue ID in older known issues documents.
  • Description - A few sentences which describe the problem. The brief description given does not necessarily describe the problem in full detail.
  • Workaround - Possible ways to work around the problem.
  • Reported Version - The earliest version in which the issue was reported.
  • Resolved Version - Version in which the issue was resolved or was no longer applicable. "N/A" indicates that the issue has not been resolved.
  • Date Added - The date the issue was added to the document (not the reported date).