| ID | Known Issues |
|---|
| 724110 | Project & System Comparison Dialog changes all channels and modules to upload
In certain cases, using the Project & System Comparison tool and changing a CompactRIO channel action to "Upload" will change all module and channel actions to "Upload".
Workaround:
Ensure the CompactRIO module settings are correct in the LabVIEW Project and select "Deploy All" from the target settings in the project.
Back to top
|
| 735928 | RIO Scan Interface (RSI) bitfile fails to install on cRIO-9055 and cRIO-9058 targets if software is installed via SystemLink
An essential component for RSI is not installed on these targets when software is installed via SystemLink. Installation will complete without issue, but when a module is deployed to the target in Scan Mode, an error will occur indicating the RIO Scan Interface bitfile is missing or corrupt.
Workaround:
- Install software via the Real-Time Software Wizard on a target that is not running the SystemLink Client software.
Back to top
|
| 737917 | "Project or Library file is corrupt" error opening LabVIEW project with certain EOL cRIO products
LabVIEW projects saved in LabVIEW 2016 or earlier with certain EOL cRIO products can generate a "Project or Library file is corrupt" error in LabVIEW 2019. This only occurs when the original project contains a C Series module as a Real-Time Scan Resource for a cRIO-910x chassis or cRIO-901x controller.
Workaround:
- Open in a version prior to LabVIEW 2019 and move the code to a non-EOL'd cRIO. Save and open in LabVIEW 2019
- Update to NI CompactRIO Device Drivers June 2019 (19.1)
Back to top
|
| 732407 | LabVIEW FPGA compilation fail occasionally with NI 9205 in slot 5 of cRIO-905x targets
LabVIEW FPGA compilations will fail occasionally when an NI 9205 is in slot 5 of cRIO-905x targets. The failure typically occurs when the top-level FPGA clock is set to 80 MHz.
Workaround:
- Retry compilation of the LabVIEW FPGA VI
- Move the NI 9205 to another cRIO slot
Back to top
|
| 737501 | Use of RSI Module Property Node in LabVIEW-built executable using CompactRIO 19.0 LabVIEW 2019 Runtime support will cause executable to fail.
CompactRIO 19.0 LabVIEW 2019 Runtime support is missing components which enable the use of the RSI module property node. When the RSI module property node is present in a built executable that uses CompactRIO 19.0 LabVIEW 2019 Runtime support, the executable will fail with an indication that a .dll file is missing, or with an error that says a refnum entry point cannot be found. The required components missing from the LabVIEW 2019 Runtime support are present in LabVIEW 2019 development support, so the RSI module property node will work in the development environment.
Workaround:
To resolve this issue on a computer with CompactRIO 19.0 LabVIEW 2019 development support installed:
- Find the two required files at the following file locations:
C:\Program Files (x86)\National Instruments\LabVIEW\2019\resource\nNIBlueBus_nCrioFixed_nRefnum.dll
C:\Program Files (x86)\National Instruments\LabVIEW 2019\resource\Framework\Providers\nNIBlueBus_nCrioFixed.dll - Copy these files to the following directory:
C:\Program Files (x86)\National Instruments\Shared\LabVIEW Run-Time\2019
To resolve this issue on computers targeted for executable installation:
- On a computer with CompactRIO 19.0 LabVIEW 2019 development support installed, find the two required files at the following file locations:
C:\Program Files (x86)\National Instruments\LabVIEW 2019\resource\nNIBlueBus_nCrioFixed_nRefnum.dll
C:\Program Files (x86)\National Instruments\LabVIEW 2019\resource\Framework\Providers\nNIBlueBus_nCrioFixed.dll - Add these files to the LabVIEW project where the LabVIEW installer for the executable program is being built
- In Installer Properties, in the Source Files category, add the two .dll files to the LabVIEW 2019 Run-Time folder
This will cause the files to be installed to the LabVIEW Runtime folder by the installer.
Back to top
|
| 727001 | Calls from System Configuration API fail with error -2147467259 fail on first call after boot for VxWorks targets
For CompactRIO targets running the VxWorks operating system, the first call to the System Configuration API after the target boots will fail with error -2147467259. Subsequent calls to System Configuration API will succeed.
Workaround:
Retry System Configuration API call until it succeeds.
Back to top
|
| 722866 | Open Thermocouple Detection on NI 9213 Module used in NI 9149 chassis may incorrectly return error -1950678943 or -1950679035 when open thermocouple is detected and sample at rate of timeout period
When the NI 9213 module is used in an NI 9149 Ethernet chassis, reading the variable with Read Variable with Timeout may return error -1950678943 or -1950679035 instead of error -65582 when an open thermocouple is detected. When this occurs, the module will also sample at the rate of the timeout.
Workaround:
- Move 9213 modules to a chassis other than the NI 9149 if one is available
- Turn off Open Thermocouple Detection and detect open thermocouple condition manually by detecting the open circuit value produced by the module
Back to top
|
| 734618 | cRIO-905x targets may rarely restart during boot up
A driver accessed during cRIO-905x boot may cause a kernel crash, which causes the target to reboot. This is a rare, random occurrence that has no effect besides causing the target to reboot. After rebooting and completing boot operations, the target will function normally.
Workaround:
No workaround required; issue fixes itself. Target runs without issue after successful reboot
Back to top
|
| 733762 | Using NI-922x modules on cRIO-905x targets may cause FPGA compilation to fail timing
FPGA compilations containing NI-922x module I/O nodes on cRIO-905x targets may fail timing due to non-diagram components.
Workaround:
- Retry the compilation repeatedly.
- Reduce the rate at which the NI-922x module samples
Back to top
|
| 729217 | Accessing properties of unconfigured modules in RSI mode may return error 65704
Attempting to access properties of modules that have not been deployed in RSI mode may result in error 65704: "CompactRIO: Could not resolve RSI module URL".
Workaround:
Deploy the modules before attempting to access module properties
Back to top
|
| 730745 | FPGA code which accesses the NI 9231 module in a cRIO-904x or cRIO-905x chassis can put the module in an error state if the FPGA code is started, stopped, and restarted in quick succession
The NI 9231 module in a cRIO-904x or cRIO-905x chassis can enter an error state if FPGA code that accesses it is started, stopped, and restarted in quick succession. The module must be removed from the chassis and replaced to correct this error state. This commonly happens when the the FPGA reference is opened with the Run VI option checked, then reset, and restarted.
Workaround:
Disable the Run VI option if the Open FPGA Reference VI settings, or leave the option enabled and do not reset and run the FPGA after opening the reference
Back to top
|
| 727706 | USB R Series DIO Write takes three cycles outside of Single-Cycle Timed Loop
Executing a USB R Series DIO Write takes three clock cycles instead of one when executed outside of a Single-Cycle Timed Loop.
Workaround:
Execute DIO Write inside Single-Cycle Timed Loop
Back to top
|