| ID | Known Issue | Affected LV Versions |
|---|---|---|
| 518755 | PXI Trigger lines 1 and 2 on the NI PXIe-782xR behave incorrectly | 2014 SP1 |
| 498902 | cRIO targets supported by Xilinx Vivado Compile Tools experience compilation failures due to timing violation errors when configured for Hybrid Interface mode | 2014, 2014 SP1 |
| 519539 | Bitfiles compiled using Xilinx Vivado Compile Tools may report skipped step or may appear to restart | 2014 SP1 |
| 515003 | LabVIEW FPGA Module 2014 with NI-RIO Device Drivers 14.5 fails to compile on cRIO-903x targets when compiling a bitfile using DMA FIFOs | 2014 |
| 523452 | Using DSA modules in LabVIEW FPGA does not prevent implicit synchronization | 2014, 2014 SP1 |
Known Issues with NI-RIO 14.0.1 and LabVIEW
| ID | Known Issues |
|---|---|
| 518755 | PXI Trigger lines 1 and 2 on the NI PXIe-782xR are swapped in NI-RIO Device Drivers 14.5 Trigger lines for NI PXIe-782xR targets experience an incorrect behavior. Workaround: Download and install the NI R Series Multifunction RIO 14.5.1 Patch (download link). |
| 498902 | cRIO targets supported by Xilinx Vivado Compile Tools experience compilation failures due to timing violation errors when configured for Hybrid Interface mode When you are using the cRIO-906x and cRIO-903x configured in Hybrid Interface mode and try to compile using Xilinx Vivado Compile Tools 2013.4, the compilation always fails for the following modules: NI 9203, NI 9205, NI 9206, NI 9220, NI 9222, NI 9223, NI 9263, NI 9264, NI 9265, NI 9269. The compilation failure refers to a non-diagram component that is required in the design. Workaround: N/A |
| 518755 | Bitfiles compiled using Xilinx Vivado Compile Tools 14 SP1 may report skipped step or may appear to restart Several C Series modules might experience an issue in which timing is not being met when using the Xilinx Vivado Compile Tools with LabVIEW 2014 or LabVIEW 2014 SP1. This issue does not affect data integrity or sampling time of the module once compiled. Workaround: N/A |
| 515003 | LabVIEW FPGA Module 2014 with NI-RIO Device Drivers 14.5 fails to compile on cRIO-903x targets when compiling a bitfile using DMA FIFOs The compilation fails due to internal components not being declared. These components include: knidmahighspeedsinkbase, knidmahighspeedsinksize, knidmahighspeedsinkbase, and knidmahighspeedsinkbase. Workaround: Install the NI-RIO Device Drivers August 2014 Distribution or upgrade to LabVIEW FPGA Module 2014 SP1. |
| 523452 | Using DSA modules in LabVIEW FPGA does not prevent implicit synchronization You might see error codes 65539 or 65582 when reading channels from two or more Dynamic Signal Acquisition (DSA) modules within the same I/O node. With CompactRIO Module Support 14.0, at the start of compilation a check was performed to ensure DSA modules read within the same I/O node were synchronized with a master clock. This check is disabled. Workaround: To avoid this warning or error, place a checkmark in the Export Onboard Clock checkbox in the module properties dialog box in the Project Explorer window. Place a checkmark in the Import Clock checkbox for any slave modules. |