NI does not actively maintain this document.
This content provides support for older products and technology, so you may notice outdated links or obsolete information about operating systems or other relevant products.
| ID | Known Issue | |||||
|---|---|---|---|---|---|---|
| 445202 | Setting the clock setting to Clk In using the SFP causes an error. Opening the NI-RFSA SFP for a device and changing the clock setting to Clk In causes an LO error and PLL phase lock failure. Workaround: N/A
| |||||
| 346518 | A delay occurs if you use the mouse to move a marker when there are many points on the graph. In Spectrum mode, with a large span-RBW ratio, or in Zero Span mode with a large RBW or acquisition time, when you enable a marker and move it using the mouse, events queue up, and there is a delay until NI-RFSA processes all the events. You may also experience a delay when clicking the arrow keys. Workaround: Change the marker position by entering a new marker value using the keypad instead of the mouse or arrow keys.
| |||||
| 368610 | Warning continues to display after you decrease the power level at the input. When the reference level of the NI-RFSA SFP is set below the power level of the signal being generated, the SFP displays a warning. If you decrease the power level at the input, you continue to receive the warning until you change the reference level. Workaround: Click the Clear button.
| |||||
| 339218 | Acquisition does not begin immediately after you clear a PLL lock error. When the NI-RFSA SFP is set to use an external Reference Clock that is not connected, a PLL lock error occurs. After you connect the clock and the device locks to the clock, the error clears, but no data displays until you change a setting in the soft front panel. Workaround: Change a setting in the soft front panel or click the Restart button, after the PLL lock error clears.
| |||||
| 448046 | The Soft Front Panel does not display custom aliases created for hardware in MAX for VST devices. For VST devices, the SFP only displays the "driver name," for example "RIO0." If the user configured an alias for the device in MAX, such as "my5645R," it is not displayed. Workaround: Remember to use the driver name when referencing the device in a debug situation, especially when working with C or NI LabWindows/CVI.
| |||||
| 453860 | The SFP does not update the Automatic VBW value when the SFP is debugging a session, until RBW is changed. When VBW is set to automatic, the value of VBW is calculated based on RBW set and the coupling ratio of VBW/RBW. When connecting the RFSA SFP to an open session using the SFP Session Access feature, if VBW is changed to automatic and the value of VBW is set to 100 kHz when RBW is shown as 800 kHz. Coupling by default is 1, so values should match. Upon changing the value of RBW, the VBW changes appropriately. Workaround: N/A
| |||||
| 449009 | The NI-RFSA SFP retains an error even after correcting the External Digital Trigger Source error in certain cases. When the NI-RFSA SFP is set to use an external digital trigger source that is not supported by the device, an error occurs. After you select a supported trigger source, the same error persists. Workaround: After selecting a supported trigger source, save the NI-RFSA SFP configuration, click Preset, then reload the NI-RFSA SFP configuration. Alternately, after selecting a supported trigger source, switch to zero span, and then switch back to last span.
| |||||
| 413889 | A signal is displayed at Center Frequency even though no signal is present at the input. This behavior only applies to the VST devices (NI 5644R/5645R/5646R). Configuring the Reference Trigger as a type other than None can display a signal at the center frequency even though no signal is present at the input. Workaround: Set the Reference Trigger type to None to remove the signal not present at the input.
| |||||
| 442518 | Clicking Preset does not reopen the previous session when SFP Session Access is enabled. If SFP Session Access is enabled for a device and the session is closed in the SFP, the SFP returns an error on clicking Preset. Workaround: Click the SFP Control (Local) button to re-open the debug session.
| |||||
| 346251 | Unsupported property or attribute error for the Contiguous Multirecord property or the NIRFSA_ATTR_CONTIGUOUS_MULTIRECORD attribute in NI-RFSA Soft Front Panel or missing extended error information. When using the NI PXI-5661 through the NI-RFSA Soft Panel, invalid configurations may produce an error message that reports that the Contiguous Multirecord property or the NIRFSA_ATTR_CONTIGUOUS_MULTIRECORD attribute is not supported. After the error condition is reported, the NI-RFSA Soft Front Panel acquisition stops. At this point, the value change that caused the error can be changed to another invalid setting and back to the original to receive the correct error message. Correcting the invalid setting allows the acquisition to continue. Workaround: When using the NI-RFSA Soft Front Panel, revert the changes that caused the error and re-apply those same changes to get the correct error message. For LabVIEW and C clients of NI-RFSA, place the niRFSA Commit VI or the niRFSA_Commit function after configuration changes that come before a fetch. This causes the correct error report to be produced. For C NI-RFSA clients, calls to niRFSA_GetError after a fetch call may still report an unsupported attribute error when the return code from fetch is VI_SUCCESS.
| |||||
| 467770 |
When using a vector signal transceiver device, changing the reference clock source from PXI_CLK to OnBoardClk requires a ten second delay for stability. Workaround: N/A.
|