ConfigurationDownload PDFSelected SectionSelected Section and Subsection(s)Entire ManualUpdated2024-11-142 minute(s) readS-Parameter Measurement LibraryAPI ReferenceLabVIEW G Configuration Use the Configuration VIs to configure the s-parameter measurement. Configure Averaging VIConfigures the averaging technique used to calculate the S-parameter for the instrument. Configure External Gain VIConfigures the maximum gain of all the paths from VST RFout to RFin so you can set the appropriate reference level for the measurements. Configure Frequency Range VIConfigures the frequency range used for S-parameter measurements. Configure IF Bandwidth VIConfigures the IF bandwidth of the measurement. Configure Stimulus VIDefines the type of RF signal used to stimulate the DUT. Configure Topology VIConfigures the type of NI and third party hardware configuration used to calculate S-parameters. Configure RFSG Power Level VIConfigures the power level used to calculate the S-parameter measurement. Configure RFSG Attenuation VIConfigures the RFSG attenuation type so that the power level at the DUT port is corrected to match the same power level set by the Configure RFSG Power Level VI. Configure Start Trigger Input VIConfigures the trigger to start the S-parameter measurement. The measurement is complete when there is a rising edge on the assigned trigger. This configuration only supports the 2 couplers per port 1 VST with solid state switch setup. If the trigger is not configured or configured for an unsupported setup the measurement is performed immediately after initiated. Configure RFSG Export Trigger VIConfigures the type and source of the trigger to export for each pulse. This configuration supports the 2 couplers per port 1 VST with solid state switch setup. If the trigger is not configured, or configured for an unsupported setup, no trigger is exported. Parent topic: S-Parameter MeasurementWas this information helpful?YesNo
Configuration Use the Configuration VIs to configure the s-parameter measurement. Configure Averaging VIConfigures the averaging technique used to calculate the S-parameter for the instrument. Configure External Gain VIConfigures the maximum gain of all the paths from VST RFout to RFin so you can set the appropriate reference level for the measurements. Configure Frequency Range VIConfigures the frequency range used for S-parameter measurements. Configure IF Bandwidth VIConfigures the IF bandwidth of the measurement. Configure Stimulus VIDefines the type of RF signal used to stimulate the DUT. Configure Topology VIConfigures the type of NI and third party hardware configuration used to calculate S-parameters. Configure RFSG Power Level VIConfigures the power level used to calculate the S-parameter measurement. Configure RFSG Attenuation VIConfigures the RFSG attenuation type so that the power level at the DUT port is corrected to match the same power level set by the Configure RFSG Power Level VI. Configure Start Trigger Input VIConfigures the trigger to start the S-parameter measurement. The measurement is complete when there is a rising edge on the assigned trigger. This configuration only supports the 2 couplers per port 1 VST with solid state switch setup. If the trigger is not configured or configured for an unsupported setup the measurement is performed immediately after initiated. Configure RFSG Export Trigger VIConfigures the type and source of the trigger to export for each pulse. This configuration supports the 2 couplers per port 1 VST with solid state switch setup. If the trigger is not configured, or configured for an unsupported setup, no trigger is exported. Parent topic: S-Parameter Measurement
Configuration Use the Configuration VIs to configure the s-parameter measurement. Configure Averaging VIConfigures the averaging technique used to calculate the S-parameter for the instrument. Configure External Gain VIConfigures the maximum gain of all the paths from VST RFout to RFin so you can set the appropriate reference level for the measurements. Configure Frequency Range VIConfigures the frequency range used for S-parameter measurements. Configure IF Bandwidth VIConfigures the IF bandwidth of the measurement. Configure Stimulus VIDefines the type of RF signal used to stimulate the DUT. Configure Topology VIConfigures the type of NI and third party hardware configuration used to calculate S-parameters. Configure RFSG Power Level VIConfigures the power level used to calculate the S-parameter measurement. Configure RFSG Attenuation VIConfigures the RFSG attenuation type so that the power level at the DUT port is corrected to match the same power level set by the Configure RFSG Power Level VI. Configure Start Trigger Input VIConfigures the trigger to start the S-parameter measurement. The measurement is complete when there is a rising edge on the assigned trigger. This configuration only supports the 2 couplers per port 1 VST with solid state switch setup. If the trigger is not configured or configured for an unsupported setup the measurement is performed immediately after initiated. Configure RFSG Export Trigger VIConfigures the type and source of the trigger to export for each pulse. This configuration supports the 2 couplers per port 1 VST with solid state switch setup. If the trigger is not configured, or configured for an unsupported setup, no trigger is exported. Parent topic: S-Parameter Measurement