Keyboard Shortcuts

Note   Shortcuts for controls grouped under a Control Tab are only usable while their Control Tab is active.
Shortcut Description
<G>, <R>, <Shift–G>, <Shift–R> Run
<P>, <Shift–P> Pause
<G>, <R> Resume
<ESC>, <Q>, <Shift–Q> Stop
<Shift–X>, <X>, <Ctrl–Q>, <Alt–F4> Exit
<A>, <Shift–A> Auto setup
<1> Trigger a single-shot acquisition
<)> (usually Shift–0) Set left channel selector to channel 0
<!> (usually Shift–1) Set left channel selector to channel 1
<#> (usually Shift–3) Set left channel selector to channel 2 (if available)
<
gt; (usually Shift–4)		 Set left channel selector to channel 3 (if available)
<Ctrl–)> (usually Ctrl–Shift–0) Set right channel selector to channel 0
<Ctrl–!> (usually Ctrl–Shift–1) Set right channel selector to channel 1
<Ctrl–#> (usually Ctrl–Shift–3) Set right channel selector to channel 2 (if available)
<Ctrl–
gt; (usually Ctrl–Shift–4)		 Set right channel selector to channel 3 (if available)
<Ctrl–D> Enable/Disable the left channel
<Ctrl–Shift–D> Enable/Disable the right channel
<Ctrl–up arrow> Decrease volts per division on the left channel
<Ctrl–down arrow> Increase volts per division on the left channel
<Ctrl–Shift–up arrow> Decrease volts per division on the right channel
<Ctrl–Shift–down arrow> Increase volts per division on the right channel
<Ctrl–A> Increment coupling on left channel
<Shift–Ctrl–A> Increment coupling on right channel
<Up arrow> Increase left channel software offset
<Down arrow> Decrease left channel software offset
<Shift–up arrow> Increase right channel software offset
<Shift–down arrow> Decrease right channel software offset
<Shift–up arrow> Increase vertical position slider
<Shift–down arrow> Decrease vertical position slider
<Ctrl–M> Launch measurement window
<Ctrl–D> Launch device configuration window
<Ctrl–left arrow> Decrease horizontal range
<Ctrl–right arrow> Increase horizontal range
<F2> Change reference position to 10%
<F3> Change reference position to 50%
<F4> Change reference position to 90%
<Shift–right arrow> Increase reference (trigger) position slider
<Shift–left arrow> Decrease reference (trigger) position slider
<Y> Increment acquisition type
<Shift–Y> Decrement acquisition type
<Ctrl–E> Display error info
<Ctrl–O> Turn on/off probe compensation
<Ctrl–T> Turn on/off trigger cursor
<Ctrl–Shift–S> Run self–calibration
<Ctrl–P> Print window
<Ctrl–X> Cut
<Ctrl–V> Paste
<Ctrl–H> Show context help
<Ctrl–S> Save waveform data
<E> Increment EXT coupling
<Shift-E> Decrement EXT coupling
<C> Toggle Cursors
<F1>, <Ctrl–?> Contents and index
Trigger Settings (TRIG) Control Tab
<S> Increment trigger source
<Shift–S> Decrement trigger source
<T> Increment trigger type
<Shift–T> Decrement trigger type
<U> Increment trigger coupling
<Shift–U> Decrement trigger coupling
<L> Increment trigger slope
<Shift–L> Decrement trigger slope
<M> Increment trigger mode
<Shift–M> Decrement trigger mode
<W> Increment trigger window mode
<Shift–W> Decrement trigger window mode
<Ctrl–W> Increment trigger delay
<Ctrl–Shift–W> Decrement trigger delay
<PgUp> Increment trigger level/low level
<PgDwn> Decrement trigger level/low level
<Shift–PgUp> Increment trigger hysteresis/high level
<Shift–PgDwn> Decrement trigger hysteresis/high level
<V> Increment TV event
<Shift-V> Decrement TV event
<O> Increment TV polarity
<Shift-O> Decrement TV polarity
<N> Increment TV line number
<Shift-N> Decrement TV line number
<F> Increment TV signal format
<Shift–F> Decrement TV signal format
<Ctrl–R> Toggle TV DC Restore
Horizontal Settings (HORIZ) Control Tab
<Z> Enable zoom
Display Settings (DISP) Control Tab
<Ctrl–M> Toggle show/hide measurement/cursor data
<Ctrl–C> Toggle show/hide configuration data
<H> Hide all data