Repair

Note Ensure that Data Record System repair procedures are performed only by qualified personnel.
Table 8. Data Record System Replacement Parts
Type NI Part Number Function and Model
Chassis 787976-01 PXIe-1092DC, 10-slot (7 hybrid slots) 3U PXI Express chassis
787975-01 PXIe-1095DC, 18-slot (5 hybrid slots) 3U PXI Express chassis
Controller 785831-01 PXIe-8861, 2.8 GHz quad-core Intel Xeon PXI controller
787567-01 PXIe-8861 non-TPM (for China)
786777-01 8 GB DDR4-2133 SO-DIMM RAM, non-ECC, for PXIe-8861
783513-05 PXIe-8880, 2.3 GHz eight-core Intel Xeon PXI controller
783513-0518 PXIe-8880 non-TPM (for China)
783813-01 8 GB Upgrade/Replacement RAM for PXIe-8880
787807-01 PXIe-8881, 3.9 GHz eight-core Intel Xeon PXI controller
787807-0118 PXIe-8881 non-TPM (for China)
787659-01 16 GB DDR4 2666 SO-DIMM RAM, ECC for PXIe-8881
Power Supply 861354-01 Data Record System AD 500W DC power supply
Camera Interface 787453-01 PXIe-1486, FPD-Link III 8-input channel
787454-01 PXIe-1486, FPD-Link III 4-channel tap
787456-01 PXIe-1487, GMSL 8-input channel
787457-01 PXIe-1487, GMSL 4-channel tap
783625-01 PXIe-7976, 2 GB DRAM PXI FPGA instrument for FlexRIO, K410T FPGA, 3.2 GB/s
787313-01 PXIe-8245, 1 Gigabit Ethernet, 4 port
787314-01 PXIe-8246, power over Ethernet, 1 Gigabit Ethernet, 4 port
Automotive Bus Interface 783639-01 PXIe-6592R, 10 Gbps high-speed serial, 4 channel
784976-01 PXIe-8238, 10 Gigabit Ethernet, 2 port
784977-01 PXIe-8240, 40 Gigabit Ethernet, 2 port
787313-01 PXIe-8245, 1 Gigabit Ethernet, 4 port
787314-01 PXIe-8246, power over Ethernet, 1 Gigabit Ethernet, 4 port
784122-01 PXIe-8510, X-NET interface, 2 port
784121-01 PXIe-8510, X-NET interface, 6 port
784122-01 PXI-8517, FlexRay interface, 2 port
786771-01 PXIe-8521, automotive Ethernet interface instrument, 100Mbit, 4 port
787312-01 PXIe-8522, automotive Ethernet interface instrument, Gigabit, 4 port
787311-01 PXIe-8523, automotive Ethernet interface instrument, 100/1000BASE-T1, 4 port
787992-01 PXIe-8623, 100/1000BASE-T automotive Ethernet interface instrument, 4 port
787104-01 NI-9962, 3-pin push-in spring terminal (4 count) for automotive Ethernet
Timing and Synchronization 782110-01 PXI-6683H, TCXO (GPS, IRIG-B, IEEE 1588) PXI synchronization
196304-30 GPS antenna
779674-01 SMA-SMB adapter
188859-01 SMB-SMB coaxial cable
Data Storage 787850-01 PXIe-8267, 15 TB SSD, data storage (5 GB/s), 1 slot
785157-01 PXIe-8394, x8 Gen 3 MXI-Express daisy chain interface
Cables 785550-01 MXI-Express cable, Gen 3 x8, copper, 1 m
785550-03 MXI-Express cable, Gen 3 x8, copper, 3 m
785549-03 MXI-Express cable, Gen 3 x4, copper, 3 m
783701-02 TRC-8543, NI-XNET CAN transceiver cable
783702-03 TRC-8546, NI-XNET LIN transceiver cable
Miscellaneous 199198-01 Assembly, slot blocker, 4HP, 3U, PXI
185365D-01 Assembly, filler panel
766489-01

Littelfuse PN: 153.5631.5801

DC power supply fuse
773765-01

Phoenix Contact PN: 1967456

External power connector
Note This table is not exhaustive. Consult your system integrator for a full list of parts specific to your system. Submit a request to NI for any additional replacement parts your system requires.

Replacing the DC Power Supply Fuse

Equipment

  • #1 Phillips screwdriver
  • #2 Phillips screwdriver

  1. Verify the input power connector is disconnected from the Data Record System.
  2. Unscrew the four screws securing the fuse cover to the DC power supply using the #1 Phillips screwdriver.

    1378

    1. Fuse Cover Screws
    2. Fuse Cover
  3. Remove the fuse cover.
  4. Unscrew the two fuse screws using the #2 Phillips screwdriver.
  5. Remove the fuse screws, lock washers, and fuse from the DC power supply.

    1378

    1. Fuse Screws
    2. Lock Washers
    3. DC Power Supply Fuse
  6. Place the new fuse (NI part number 766489-01) in the DC power supply.
  7. Secure the fuse with the two lock washers and two fuse screws using the #2 Phillips screwdriver.
  8. Torque the fuse screws to 0.76 N · m (6.7 lb · in.).
  9. Replace the fuse cover.
  10. Torque the fuse cover to the DC power supply using the #1 Phillips screwdriver to 0.56 N · m (5.0 lb · in.).

Replacing PXI Instruments

This topic contains general installation instructions for installing PXI instruments in the chassis. For specific instructions for your instrument, refer to the instrument documentation.

Equipment

  • #1 Phillips screwdriver

  1. Connect the DC power source to the chassis.
  2. Ensure that the chassis is powered off.
  3. Disconnect all cables from the PXI instrument.
  4. Unscrew the captive screws on the PXI instrument using the #1 Phillips head screwdriver.
  5. Eject the PXI instrument from the chassis slot using the injector/ejector handle.
  6. Slide the PXI instrument out of the chassis.
  7. Slide the new PXI instrument in the open chassis slot.
  8. Lock the PXI instrument in the chassis slot using the injector/ejector handle.
  9. Screw in the captive screws on the PXI instrument using the #1 Phillips head screwdriver.
  10. Connect the appropriate cables to the PXI instrument.